• CBG SOURCING®

    Professional Concrete Crack Repair Systems

    • Store
    • Contact us
  • Phone: 706-956-4278 | Business Address: 1019 Quaker Ridge Way, Johns Creek, GA 30097 | Email: info@cbgsourcing.com | CBG Sourcing is operated by Claremont-Branan Group, LLC.
    Get directions
    Business hours
CBG SOURCING®

Professional Concrete Crack Repair Systems

Epoxy injection kits, resins, repair pastes, ports, tools, and contractor packs for foundation, basement, and structural concrete repairs. 

Phone: 706-956-4278 | Business Address: 1019 Quaker Ridge Way, Johns Creek, GA 30097 | Email: info@cbgsourcing.com | CBG Sourcing is operated by Claremont-Branan Group, LLC.

Scroll for Products

CBG SOURCING®
Categories
CBG Sourcing Epoxy Injection Cartridge Refill Featuring Polygem LCR (2-Pack, 10 fl oz Each)
+8
+7
+6
+5
+4
+3
+2

CBG Sourcing Epoxy Injection Cartridge Refill Featuring Polygem LCR (2-Pack, 10 fl oz Each)

Store/Bulk & Contractor Packs/Volume Multi-Packs
$119.95
Cartridge 2-Pack
Estimated delivery time
FREE Shipping — Contiguous U.S. (48 States)
In stock
1
Minimum purchase quantity: 1 items
Have questions?

CBG Sourcing Epoxy Injection Cartridge Refill Featuring Polygem LCR (2-Pack, 10 fl oz Each)

Store/Bulk & Contractor Packs/Volume Multi-Packs
Product Details
UPC: 850072775210
Brand: CBG SOURCING

CBG SOURCING Epoxy Injection Cartridge Refill Featuring Polygem LCR (2-Pack, 10 fl oz (296 mL) Each)

At a Glance

  • Best For: Structural injection of cracks in concrete. The resin penetrates cracks above .005” (0.13 mm). Orientation: vertical walls, where the crack must first be sealed and ports mounted with LCR Epoxy Repair Paste, and horizontal slabs. For dry, non-actively-leaking cracks. Wall surface (where the paste and ports go): must be dry and free of contaminants, dirt, grease, and flaking paint. Not for contaminated or oily surfaces.

Crack Width & Coverage Guide

  • Crack Width Suitability: Engineered for cracks approximately 1/16 in. (1.6 mm) to 1/8 in. (3.2 mm) wide in poured concrete walls and slabs.
  • Single Cartridge (10 fl oz (296 mL)) Coverage:
    • Fills approx. 4 linear feet (1.2 m) of a 1/16 in. (1.6 mm) crack in a standard 6 in. (152 mm) thick wall.
    • Fills approx. 2 linear feet (0.6 m) of a 1/8 in. (3.2 mm) crack in a standard 6 in. (152 mm) thick wall.
    • Note: Wider cracks, thicker foundation walls, or unseen internal voids will require additional resin.
  • Complete Kit (2 Cartridges) Coverage:
    • Repairs up to 8 linear feet (2.4 m) of a 1/16 in. (1.6 mm) crack (ideal for typical 8 ft. (2.4 m) basement wall joints).
    • Repairs up to 4 linear feet (1.2 m) of a 1/8 in. (3.2 mm) crack.
  • Skill Level: DIY or Pro. Mix only the cartridge you are ready to use and inject within 30 minutes.
  • What’s Included: 2 × 10 fl oz (296 mL) Polygem LCR injection cartridges, 20 fl oz (592 mL) total; each has Part A resin + Part B hardener. One mixing plunger/rod and one dispensing nozzle come with each cartridge. Ports, paste, and gun are sold separately.

Key Features

  • Two cartridges for longer cracks, multiple cracks, or refilling a kit.
  • 100% solids, two-component, moisture-insensitive epoxy; no VOCs, no solvents.
  • Standard caulking-gun application with slow, even pressure.

Required & Pairs With

  • Required for wall cracks: LCR Epoxy Repair Paste + Surface 50-Pack / Surface 100-Pack / Corner 7-Pack.
  • Starting from scratch: Polygem LCR Concrete Crack Repair Kit.
  • Other sizes: Single · 3-Pack.
  • Gun: Standard caulking gun (not sold on CBGSourcing.com).
  • Cleanup: Handy Jack® Wipes (60 Count).

Technical Specs — Polygem LCR Epoxy Injection Resin

Spec Value
Gel / tack-up time Allow ports to tack up for at least 30–90 minutes (depending on room temperature) before sealing along the crack line. Full cure: 24 hrs. (see below).
Mix ratio (by volume) 1A to 1B
Pot life (100 gms), ASTM D-2471 60 min.
Working time (73°F – 23°C – 100 gms) 30 min.; thin film working time 1 hr.
Full cure time 24 hrs. (Allow the full 24 hour cure before removing clamps, sanding, painting, or putting an anchor or patch into service.)
Viscosity 580 cps (low viscosity, LV).
Application temperature 72–90°F (23–32°C), “DO NOT install on damp or wet surfaces or at temperatures below 72°F (23°C) or above 90°F (32°C).”
Compressive strength (ASTM D-695) 6,798 psi
Tensile strength (ASTM D-638) 2,323 psi
Shore D hardness (ASTM D2240) 81 D
Heat deflection temp (ASTM C882) 115°F (46°C)

Documentation

See the Polygem technical bulletins and Safety Data Sheets below. Read the product labels and Safety Data Sheets before use.

Shipping

We ship to the 48 contiguous states. For Alaska, Hawaii, or bulk accessory orders, contact us for a quote.

Technical documents (Polygem)

  • LCR Epoxy Injection Resin technical bulletin (PDF)
  • LCR Epoxy Repair Paste technical bulletin (PDF)
  • Safety data sheet 10004207-10004211 (PDF)
  • Safety data sheet 10004198-10004203 (PDF)

Frequently Asked Questions

What comes in this 2-pack?

Two 10 fl oz (296 mL) Polygem LCR injection resin cartridges, 20 fl oz (592 mL) total. Each cartridge comes with its own mixing plunger and dispensing nozzle. Ports, paste, and the gun are sold separately. Wall cracks need paste to mount the ports and seal the crack surface before injection.

What cracks is the resin for?

Dry, non-actively leaking cracks in poured concrete, typically about 1/16 in to 1/8 in wide. The resin penetrates cracks above .005 in (0.13 mm). It is not for actively leaking cracks.

How much will the 2-pack cover?

Up to 8 linear ft of a 1/16 in crack, or up to 4 linear ft of a 1/8 in crack, in a standard 6 in thick wall. Wider cracks, thicker walls, or voids need more resin.

What is the viscosity?

580 cps. This is the low-viscosity (LCR LV) injection resin.

What gun do I need?

A standard caulking gun. It is not sold on CBGSourcing.com.

Show More
Customer reviews
Reviews only from verified customers
No reviews yet. You can buy this product and be the first to leave a review.
Powered by Lightspeed
Display prices in:USD

Contact

Phone: 706-956-4278 | Business Address: 1019 Quaker Ridge Way, Johns Creek, GA 30097 | Email: info@cbgsourcing.com | CBG Sourcing is operated by Claremont-Branan Group, LLC.
info@cbgsourcing.com
cbgsourcing.com

Connect

Facebook
X (formerly Twitter)
Pinterest
Instagram
YouTube
Share Share Pin
© CBG SOURCING® Report abuse Cookie settings
Powered by Lightspeed